|
| Author | Message |
|---|
walkie
Senior Developer
Posts : 5086
Join date : 2012-11-05
Age : 47
Location : UK
 |  Subject: Distorted Melted Bubble  Fri Dec 28, 2012 4:34 pm | |
| |
|
  | |
cantina_patron
TIG Benefactor
Posts : 5371
Join date : 2011-10-26
Age : 52
Location : UK
| | Subject: Re: Distorted Melted Bubble Fri Dec 28, 2012 5:12 pm | |
| I've got a Palitoy Hoth Trooper with similar heat distortion on one side of the bubble. I have always presumed that it came from the factory like it. |
|
| | |
walkie
Senior Developer
Posts : 5086
Join date : 2012-11-05
Age : 47
Location : UK
| | Subject: Re: Distorted Melted Bubble Fri Dec 28, 2012 5:22 pm | |
| |
|
| | |
cantina_patron
TIG Benefactor
Posts : 5371
Join date : 2011-10-26
Age : 52
Location : UK
| | Subject: Re: Distorted Melted Bubble Fri Dec 28, 2012 6:50 pm | |
| - walkie wrote:
- thank you
No problem. I'll take a photo tomorrow, so that you can compare it to yours. |
|
| | |
walkie
Senior Developer
Posts : 5086
Join date : 2012-11-05
Age : 47
Location : UK
| | Subject: Re: Distorted Melted Bubble Fri Dec 28, 2012 7:41 pm | |
| |
|
| | |
cantina_patron
TIG Benefactor
Posts : 5371
Join date : 2011-10-26
Age : 52
Location : UK
| | Subject: Re: Distorted Melted Bubble Sat Dec 29, 2012 7:08 am | |
| They're not the best, but hopefully these pics are clear enough for you to see the distortion to the bubble where it was applied to the cardback. [img]  [/img] [img]  [/img] |
|
| | |
walkie
Senior Developer
Posts : 5086
Join date : 2012-11-05
Age : 47
Location : UK
| | Subject: Re: Distorted Melted Bubble Sat Dec 29, 2012 7:20 am | |
| Perfect, just the answer and proof I was after.
|
|
| | |
Bjamin_S
New User
Posts : 4
Join date : 2012-11-29
| | Subject: Re: Distorted Melted Bubble Sat Dec 29, 2012 6:48 pm | |
| - walkie wrote:
- Perfect, just the answer and proof I was after.
That kind of distortion in the bubble is very, very common - in fact, calling it distortion is possibly being a touch dramatic. In some cases you'll wind up with a raised area, or large sections of the bubble that isn't properly sealed to the card. Remember that these thin plastic bubbles were heat pressed, or stamped onto cards. Some kind of alteration in shape is almost inevitable as part of that process. |
|
| | |
walkie
Senior Developer
Posts : 5086
Join date : 2012-11-05
Age : 47
Location : UK
| | Subject: Re: Distorted Melted Bubble Sat Dec 29, 2012 6:51 pm | |
| Believe it or not I had potential buyer for this MOC but I think they through the bubble had been tempered with.
|
|
| | |
Bjamin_S
New User
Posts : 4
Join date : 2012-11-29
| | Subject: Re: Distorted Melted Bubble Sat Dec 29, 2012 6:57 pm | |
| - walkie wrote:
- Believe it or not I had potential buyer for this MOC but I think they through the bubble had been tempered with.
That's a bit nuts on the buyer's part. The ESB 41 At-At driver in particular seems to have this flaw - I've had a few over the years, and I think they all had this to some degree. |
|
| | |
Sponsored content
| | Subject: Re: Distorted Melted Bubble | |
| |
|
| | |
|
